
The Best Epoxy Remover
Epoxy resin is lauded as an excellent adhesive used for fixing and patching up damaged surfaces. However, a fully cured resin can be hard to remove when it gets to the wrong places.
Accidents are bound to happen even with the best epoxy resin in UAE. As a result, we recommend that you keep the right epoxy remover at all times to avoid damaging your beautiful surfaces.
The Best Epoxy Remover
The most important factor to consider when choosing the best epoxy remover is the surface affected. Not all epoxy removal methods are effective on all surfaces. We have compiled the best epoxy removers and the surfaces they are most effective on.
Best Epoxy Remover for Glass and Plastics
Getting rid of resin residues and smudges on glasses and plastics is very hard because of the delicate nature of both surfaces. Therefore, you have to be extra careful not to damage them. The best method to use in this instance is isopropyl alcohol.
Soak a paper towel in isopropyl alcohol and then rub it on the epoxy-stained surface. The alcohol should easily break the adhesive bonds, especially if the resin is not fully cured. However, if the resin is cured fully, you might want to go with a stronger solvent, for instance, denatured alcohol or paint thinner.
Soak a cloth in denatured alcohol/paint thinner and apply it on the affected surface to weaken the resin bonds. Then, using a plastic or wooden tool, gently scrap the soft epoxy from the surface. You can then use a clean, wet rag to remove the remaining deposits on the glass or plastic.
Best Epoxy Remover for Wooden and Concrete Floors
Resin is a cost-efficient way of finishing floors and repairing damages. However, an exposed resin is very risky as it can lead to trips and falls. Therefore, getting rid of exposed resin is very important as soon as you finish repairing the damages.
Wooden floors are very sensitive. Using alcohol or paint thinners could discolor or even damage them. The best epoxy remover for wooden and concrete floors is acetone. Acetone can loosen the epoxy on the floor, allowing it to peel away easily. Also, acetone evaporates quickly into gaseous state without damaging the wooden surface.
You can also use a heat gun to soften the cured epoxy before peeling it away with a scrapping tool. Resin requires temperatures of up to 200˚C to break its tight bonds. As a result, the high heat can easily damage your wooden floor if you are not careful.
Therefore, ensure the heat gun is several inches above the floor and directly pointed at the resin only. Heat the epoxy resin smudge in a circular motion to distribute the heat evenly. Also, ensure you wear thick gloves at all times to protect your hands from burning and a respirator to avoid inhaling the dangerous resin fumes.
Best Epoxy Remover for Metal and Hard Surfaces
Epoxy removers can also be used on hard and non-porous surfaces, such as metal. These hard surfaces are sturdy and can withstand most of the chemical adhesive removers available in stores. We prefer aerosol spray refrigerant, which freezes the resin, making it easy to scrap away. However, chemical adhesive removers are highly toxic.
Therefore, you should always use safety gear, such as gloves and a respirator, to avoid contact with the chemicals either in liquid or gaseous states. Also, work in a well-ventilated area to avoid respiratory complications.
Best Epoxy Remover for Fabrics
Fabrics are the most delicate surfaces to work with. As a result, most of the methods we have highlighted above are likely to damage your clothes. For instance, scraping will destroy the fabric, while acetone and paint thinners will discolor and dissolve it. Only two methods work best on fabrics: heat and vinegar.
The heat method is effective on tough fabrics, such as cotton and linen, which are not affected by boiling water. The process is simple: immerse the affected area in boiling water and then lift it out after a few seconds. Use tongs to peel away the resin. You can return the fabric into the boiling water several times to make the resin softer.
Make sure you wear protective gear when handling the hot cloth. For delicate fabrics, such as shrinking wool and melting synthetic materials, vinegar is the way to go. Soak the affected area in vinegar to loosen the epoxy. Then, wash it with cold water.
Having the right epoxy remover is as important as having the best resin in Dubai. It will help you get rid of the ugly epoxy smudges on your surfaces. However, the kind of surface you apply the resin should always dictate the type of epoxy remover you use.